Electric rolling shutter door installation electric shutter door maintenance

Electric rolling shutters are now used very extensively, and some factory buildings have access to the doors of vehicles, and some residential garages use electric rolling shutters. Because of its beautiful appearance, complete functions, convenient control, and manual operation during power outage, it is used in large quantities. Next Xiaobian introduced electric shutter doors and electric shutter doors for everyone.

Electric shutter door installation

1. First draw a line at the position of the door frame that needs to be installed. Show the size, and then find the staff to design a suitable electric shutter doors, it is worth noting that the height of the frame is a little higher than the height of the door.

2. First, fix the door frame of the electric rolling shutter door, and first remove the fixing plate at the lower part of the door frame. (Note: The grooves are reserved on both sides of the hole, and after being calibrated, the wooden wedges are fastened, and the iron feet of the frame are welded to the embedded iron plate pieces. The cement mortar or the fine stone concrete with a strength of not less than 10 MPa is firmly embedded. can.)

3. Install the main door leaf of the electric shutter door leaf. It must be ensured that the electric roller shutter door is integrated with the wall body, and the sealing property should be well done. Then the hole and wall should be painted. After painting is completed, the door joints should be evenly leveled, and the electric shutter doors should be free and light, and must not be overtightened, loosened or rebounded.

Electric shutter door maintenance

1. During the use of the electric shutter door, it is necessary to keep the stability of the controller and voltage as far as possible. It is forbidden to install it in a very humid environment. Do not open the remote controller at will. If it is found that there is wire winding on the door body, tying, etc. . Pay attention to whether the channel is blocked, hinder the door body from falling, and stop the motor operation if any abnormal response occurs.

2, to regularly check the electric shutter door up and down stroke switch, add lubricant to the travel controller, to maintain normal good operation, in addition, the operator manually control the shutter door, checker operation, proofreading the upper and lower travel switch position, so that electric When the rolling shutter door is opened or closed, it is in proper position, and the electric rolling shutter door shall be prevented from being pushed or flushed or reversed in the inspection process. If there is an emergency, the rotation shall be stopped immediately and the power shall be cut off.

3, the operator is best to regularly check the manual switch and manual lifting decoration of the electric shutter door to prevent the electric shutter door from malfunctioning or causing unnecessary safety accidents in case of emergency.

4. Keep the track running smoothly, clear the track of the electric rolling shutter door in time, and keep the inside clean. The shutter door motor and the drive chain should always be filled with lubricant. Check the components in the control box and the switch control box, tighten the wiring port, tighten the screws, etc. ,Dust and dirt on the inside of the control box, the surface, and the button to prevent the button from jamming and not rebound.

Electric shutter door structure

The electric shutter door is mainly composed of a door body, a driver, and a control system. The door body is made of high-quality stainless steel and aluminum alloy special profiles. It is hinged on the principle of parallelogram and has a flexible and flexible stroke. The drive adopts special motor drive, worm gear deceleration, automatic clutch or manual clutch, automatic opening and closing when automatic clutch and power failure, manual opening and closing when manual clutch and power failure, control system has control panel, push button switch, and other according to the user. The demand is equipped with a wireless remote control device. Can be equipped with a scrolling display, display 500 words of display content, but also equipped with smart infrared dual probe anti-collision device, 20-30CM case or foreign body can automatically return to run, thus protecting the safety of vehicles and pedestrians.

Editor's summary: About the installation of the electric rolling shutter and the maintenance of the electric rolling shutter door are introduced here, I hope to be helpful to everyone. If you want to know more related information, you can pay attention to this website information.

Electric blinds electric opening and closing curtains electric shaver electric sofa electric juicer